Corrosion Technology Systems, Inc.
Waterstop/Infiltration/Exfiltration Products
InstaPlug No. F-180
Rapid setting hydraulic water plug that will seal active water leaks and allow continuous
rehabilitation work on concrete structures. This material will set in 60 -90 seconds and cure
completely in one hour. It is also used to fill small voids and for anchoring applications. (Sauereisen)
H2OPruf No. F-190
Cementitious based negative side waterproofing system specifically designed to withstand
hydrostatic pressures that cause water seepage in below grade structures. Two 1/16th inch coats
will withstand up to 70 feet of water head pressure. It can be applied by brush or spray, including
rotary spray equipment used for manholes. (Sauereisen)
Hydroactive Polyurethane Grout No. F-370
Catalyzed hydrophobic grout that reacts with moisture and expands to 20 times its volume to seal
leaks, cracks, joints and voids. It bonds tenaciously to practically any substrate, wet or dry, has
excellent chemical resistance and is safe for potable water.(Sauereisen)
Fib-R-Thane Chimney Seal No. 88
Elastomeric lining composed of fiber-reinforced, asphalt-modified urethane. Two component,
chemical resistant seal that can be troweled onto the chimney sections of manholes to prevent
water inflow. As a high solids elastomer, Fib-R-Thane Chimney Seal maintains excellent elasticity
and adhesion over a temperature range of -30°F to 250°F while resisting acids, alkalies and
salts.(Sauereisen)
Combination Substrate Repair & Infiltration Prevention Product
Substrate Resurfacer No. F-121
Single component, high strength, rapid set Portland cement based product for repairing,
resurfacing and waterproofing masonry structures. This material will restore structural integrity and
prevent infiltration in concrete and brick structures. It is designed for rotary and straight shot spray
application and can be applied at various thicknesses in one pass. (Sauereisen)
Substrate Repair Materials
Underlayment and Repair Mortar No. F-120
Single component, high strength, rapid set Portland cement based repair mortar that is available in
trowel, castable and gunite grades. The trowel grade can be applied vertically and overhead and
can be topcoated with epoxy in 5 hours. (Sauereisen)
Filler Compound No. 209
Three component, epoxy formulation that is specifically designed to fill voids, irregularities and air
pockets in concrete. No. 209 will provide a smooth surface ready for application of protective
compounds in 3 hours. This material is also available in a fast setting grade that can be top coated
in 1 hour. Either formulation is suitable for application over damp or dry concrete. Application is
performed with a rubber K&R trowel. (Sauereisen)
Corrosion Resistant Linings
SewerGard Epoxy No. 210 Systems
Self priming, moisture tolerant epoxy systems that are completely resistant to the micro-biologically
induced corrosion common to municipal wastewater applications. They are available in aggregate
filled trowel ( No. 210T ) and rotary spray ( No. 210RS ) versions, as well as a fiber filled airless
spray version (No. 210S ). These products will bond to damp concrete and cure in the presence
of moisture. The No. 210RS is used in the Sauereisen 60 Minute Solution and allows manholes to
be efficiently lined from street level with minimal entry into the manhole. (Sauereisen)
Precast Polymer Manholes / Pipe
Fabri-Kast® Solid Cast Polymer Structures
Polymer pipes, manholes, and sumps used in the same mannor as traditional concrete cast
materials, with the added benefit of complete corrosion resistance and added strength. Municipal
wastewater and chemical processing industries have the greatest demand for the Fabri-Kast line of
products. The Fabri-Kast Solid Cast Polymer line of pipe products feature push-on joint
technology that employs a combination of couplings and elastomeric gaskets. The pipe products -
which range in size from 12 inches to 12 feet in diameter - are ideally suited for use in direct burial,
slip lining and microtunneling/drilling applications. Moreover, as "rigid conduits" Fabri-Kast Solid
Cast Polymer pipe products require no special bedding or reinforcement in direct burial
applications. (Fabri-Kast)
InstaPlug No. F-180
Rapid setting hydraulic water plug that will seal active water leaks and allow continuous
rehabilitation work on concrete structures. This material will set in 60 -90 seconds and cure
completely in one hour. It is also used to fill small voids and for anchoring applications. (Sauereisen)
H2OPruf No. F-190
Cementitious based negative side waterproofing system specifically designed to withstand
hydrostatic pressures that cause water seepage in below grade structures. Two 1/16th inch coats
will withstand up to 70 feet of water head pressure. It can be applied by brush or spray, including
rotary spray equipment used for manholes. (Sauereisen)
Hydroactive Polyurethane Grout No. F-370
Catalyzed hydrophobic grout that reacts with moisture and expands to 20 times its volume to seal
leaks, cracks, joints and voids. It bonds tenaciously to practically any substrate, wet or dry, has
excellent chemical resistance and is safe for potable water.(Sauereisen)
Fib-R-Thane Chimney Seal No. 88
Elastomeric lining composed of fiber-reinforced, asphalt-modified urethane. Two component,
chemical resistant seal that can be troweled onto the chimney sections of manholes to prevent
water inflow. As a high solids elastomer, Fib-R-Thane Chimney Seal maintains excellent elasticity
and adhesion over a temperature range of -30°F to 250°F while resisting acids, alkalies and
salts.(Sauereisen)
Combination Substrate Repair & Infiltration Prevention Product
Substrate Resurfacer No. F-121
Single component, high strength, rapid set Portland cement based product for repairing,
resurfacing and waterproofing masonry structures. This material will restore structural integrity and
prevent infiltration in concrete and brick structures. It is designed for rotary and straight shot spray
application and can be applied at various thicknesses in one pass. (Sauereisen)
Substrate Repair Materials
Underlayment and Repair Mortar No. F-120
Single component, high strength, rapid set Portland cement based repair mortar that is available in
trowel, castable and gunite grades. The trowel grade can be applied vertically and overhead and
can be topcoated with epoxy in 5 hours. (Sauereisen)
Filler Compound No. 209
Three component, epoxy formulation that is specifically designed to fill voids, irregularities and air
pockets in concrete. No. 209 will provide a smooth surface ready for application of protective
compounds in 3 hours. This material is also available in a fast setting grade that can be top coated
in 1 hour. Either formulation is suitable for application over damp or dry concrete. Application is
performed with a rubber K&R trowel. (Sauereisen)
Corrosion Resistant Linings
SewerGard Epoxy No. 210 Systems
Self priming, moisture tolerant epoxy systems that are completely resistant to the micro-biologically
induced corrosion common to municipal wastewater applications. They are available in aggregate
filled trowel ( No. 210T ) and rotary spray ( No. 210RS ) versions, as well as a fiber filled airless
spray version (No. 210S ). These products will bond to damp concrete and cure in the presence
of moisture. The No. 210RS is used in the Sauereisen 60 Minute Solution and allows manholes to
be efficiently lined from street level with minimal entry into the manhole. (Sauereisen)
Precast Polymer Manholes / Pipe
Fabri-Kast® Solid Cast Polymer Structures
Polymer pipes, manholes, and sumps used in the same mannor as traditional concrete cast
materials, with the added benefit of complete corrosion resistance and added strength. Municipal
wastewater and chemical processing industries have the greatest demand for the Fabri-Kast line of
products. The Fabri-Kast Solid Cast Polymer line of pipe products feature push-on joint
technology that employs a combination of couplings and elastomeric gaskets. The pipe products -
which range in size from 12 inches to 12 feet in diameter - are ideally suited for use in direct burial,
slip lining and microtunneling/drilling applications. Moreover, as "rigid conduits" Fabri-Kast Solid
Cast Polymer pipe products require no special bedding or reinforcement in direct burial
applications. (Fabri-Kast)
| Products for Restoration and Protection of Wastewater Infrastructures |