Corrosion Technology Systems, Inc.
| SPECIALTY COATINGS |
Steelcote 303A
Is a cementitious coating/primer that is applied over rusted surfaces that are wire brushed to provide
a protective barrier that will keep the metal substrates from continuing to rust. It may be used as a
primer or finish coat. It is a water-borne material and therefore water tolerant and may be installed
on damp or moist surfaces. It may be used on steel, tanks and equipment as a primer with an
appropriate topcoat for exterior or chemical resistance. (Steelcote)
MCU 2100 Type VIII Primer
Is a single package, quick dry aromatic moisture cured urethane primer, that adheres to power tool
cleaned, rusted surfaces where sandblasting is not possible. It can be recoated in 4 hours. In
addition, it contains micaceous iron oxide which provides excellent chemical resistance. A 3 mil
DFT can be acheived in a single coat and the filler provides a good tooth or profile for successive
coats to bond. (Steelcote)
MCU 2100 Type IV
Is a single component moisture cured urethane with 316L stainless steel filler. It bonds to rusty wire
brushed steel, and other well bonded coatings, plus it dries quickly (1-2 hours) for fast recoating and
short down times and can be applied at temperatures as low as 28 F. Its versatility allows for two
coats to be applied in the same day. It provides excellent abrasion and chemical resistance and is
USDA approved. Two coats of Type IV over one coat Type VIII will provide an extremely dense,
heavy duty coating system even over minimally prepared steel surfaces. (Steelcote)
MCU 2100 Type IX
Single component moisture cured urethane with bright shiny stainless steel fillers. It has many of the
same features as MCU-2100 Type IV, but with slightly less abrasion and corrosion resistance.
Speedepoxy
A vinyl modified, quick dry film epoxy designed as a tie coat over most material. It is formulated in
an easy 1:1 ratio and can be topcoated in 30 minutes.
Tile-X 2000
Is a very tough, durable, high build acrylic modified coating, where an attractive non-yellowing, high
gloss finish is required. In addition it provides a stain resistant, anti-graffiti, tile-like finish.
Steelmastic 168
Self-priming, limited preparation, direct to rust, high-build coating for maximum corrosion protection.
Epo-Mastic DTO
Formulated to bond to oil or grease contaminated concrete or steel. It can be used as a primer coat
for other systems or as a stand-alone coating and is used most often when all other coatings have
failed.
Steelcote 303A
Cementitious coating/primer that is applied over rusted surfaces that are wire brushed to provide a
protective barrier that will keep the metal substrates for continuing to rust. It may be used as a
primer or finish coat.
BFB Flexible
Self-leveling 100% solids elastomer to give chemical resistance and flexibility to a seamless floor
coating. It is recommended for asphalt surfaces (unlike any other coating) and is also recommended
for wood, steel and concrete surfaces.
Thiocaulk H-705A
Is a polysulfide joint sealant designed for both horizontal and vertical joints. It is an excellent
expansion joint that provides chemical resistance where epoxies and urethanes fall short. It can
handle hydrocarbons, solvents, organic acids, esters, and inorganic liquids.
Is a cementitious coating/primer that is applied over rusted surfaces that are wire brushed to provide
a protective barrier that will keep the metal substrates from continuing to rust. It may be used as a
primer or finish coat. It is a water-borne material and therefore water tolerant and may be installed
on damp or moist surfaces. It may be used on steel, tanks and equipment as a primer with an
appropriate topcoat for exterior or chemical resistance. (Steelcote)
MCU 2100 Type VIII Primer
Is a single package, quick dry aromatic moisture cured urethane primer, that adheres to power tool
cleaned, rusted surfaces where sandblasting is not possible. It can be recoated in 4 hours. In
addition, it contains micaceous iron oxide which provides excellent chemical resistance. A 3 mil
DFT can be acheived in a single coat and the filler provides a good tooth or profile for successive
coats to bond. (Steelcote)
MCU 2100 Type IV
Is a single component moisture cured urethane with 316L stainless steel filler. It bonds to rusty wire
brushed steel, and other well bonded coatings, plus it dries quickly (1-2 hours) for fast recoating and
short down times and can be applied at temperatures as low as 28 F. Its versatility allows for two
coats to be applied in the same day. It provides excellent abrasion and chemical resistance and is
USDA approved. Two coats of Type IV over one coat Type VIII will provide an extremely dense,
heavy duty coating system even over minimally prepared steel surfaces. (Steelcote)
MCU 2100 Type IX
Single component moisture cured urethane with bright shiny stainless steel fillers. It has many of the
same features as MCU-2100 Type IV, but with slightly less abrasion and corrosion resistance.
Speedepoxy
A vinyl modified, quick dry film epoxy designed as a tie coat over most material. It is formulated in
an easy 1:1 ratio and can be topcoated in 30 minutes.
Tile-X 2000
Is a very tough, durable, high build acrylic modified coating, where an attractive non-yellowing, high
gloss finish is required. In addition it provides a stain resistant, anti-graffiti, tile-like finish.
Steelmastic 168
Self-priming, limited preparation, direct to rust, high-build coating for maximum corrosion protection.
Epo-Mastic DTO
Formulated to bond to oil or grease contaminated concrete or steel. It can be used as a primer coat
for other systems or as a stand-alone coating and is used most often when all other coatings have
failed.
Steelcote 303A
Cementitious coating/primer that is applied over rusted surfaces that are wire brushed to provide a
protective barrier that will keep the metal substrates for continuing to rust. It may be used as a
primer or finish coat.
BFB Flexible
Self-leveling 100% solids elastomer to give chemical resistance and flexibility to a seamless floor
coating. It is recommended for asphalt surfaces (unlike any other coating) and is also recommended
for wood, steel and concrete surfaces.
Thiocaulk H-705A
Is a polysulfide joint sealant designed for both horizontal and vertical joints. It is an excellent
expansion joint that provides chemical resistance where epoxies and urethanes fall short. It can
handle hydrocarbons, solvents, organic acids, esters, and inorganic liquids.